|
 24
1/24 scale Club-Racing
Chassis Components
for chassis T24002HPF &
T24004HPF |
|
Order through your dealer or PURCHASE online
with Secure Store: |
|
T2401 |
Chassis center section, glass-reinforced Nylon
|
 |
$4.99
|
|
T2401SP |
Chassis
center section specially drilled and milled, fitted with contact rails, new
TSC25 stainless-steel guide pin set dead-center, for serious club racing.
|
 |
$14.49
|
|
THP2412 |
TSR/Ortmann
high performance rear racing tires, hand-cast in a silicone-urethane
compound, fantastic traction, very long-lasting. Fit over the T2403 or
THP2406 wheels. Sold in pair.
|
 |
$9.99
|
|
THP2402 |
Finest pro-racing foam
rubber tire glued & trued on setscrew aluminum rear wheels. Not for use on
plastic track unless with traction magnet or if traction compounds are
used. Pair: |
 |
$12.49
|
|
THP2403 |
Free-rotation front
aluminum wheels. Uses standard T2411 standard front tire. Grooved for
lighter weight.
Pair: |
 |
$5.99
|
|
THP2405 |
Aluminum setscrew rear
wheels without tires. Use them to install your own rubber compound and grind
it to size, or cast your own silicon tires.
Pair: |
 |
$6.49
|
|
T2406 |
Optional
side body bracket, glass-reinforced Nylon Each: |
 |
$0.99
|
|
T2407 |
Automatic
Body Mounting Tool, glass-reinforced Nylon |
|
$0.99
|
|
T2408 |
Front
axle, stainless steel |
 |
$1.29
|
|
T2409 |
Rear
axle, stainless steel |
|
$1.19
|
|
THP2404 |
Rear
axle, drill blank (will not be marked by setscrews) |
|
$3.28
|
|
T2410 |
Body
mounting pin tubing, stainless steel Each: |
|
$0.79
|
|
T2411 |
Front
tire, silicone-neoprene compound
Each: |
|
$1.99
|
|
T2413 |
Contact
rail, positive lead, stainless steel |
 |
$0.42
|
|
T2414 |
Contact
rail, negative lead, stainless steel |
|
$0.45
|
|
T2415 |
TSR
electric motor with 11T steel pinion |
|
$8.99
|
|
TD301 |
TSR High Performance
motor. The fastest home-racing motor available anywhere. Fits TSR as well as
many other cars. CCW rotation seen from can end. Supplied without a drive
pinion. Fits all .078" pinions.
Used exclusively for D3 Racing Can-Am. For this specific use, TSR recommends
using Parma-PSE pinion and crown gears, from 8-28 for short tracks to 9-27
for long tracks.
WARNING:
Maximum recommended voltage: 13-Volts. Not to be used with power packs
supplied in standard racing sets. Requires 4-amp minimum current. Failure
to use a proper power supply may damage this motor.
WARNING:
rotation is counter clockwise when seen from the pinion side of the motor.
Do not use in incorrect rotation as it will damage the motor.
|
|
$10.95
|
|
T2416 |
Chassis pan,
nickel-plated steel |
 |
$9.49
|
|
THPR45 |
Aluminum 64-P setscrew
spur gear / steel pinion gear ratio 14-45.Will
fit sidewinder Fly and GB-Track cars for a much smoother gear setup.
Must be used with THP2404 axle. |
 |
$9.79
|
|
THPR46 |
Aluminum 64-P setscrew
spur gear / steel pinion gear ratio 13-46.
Will fit sidewinder Fly and GB-Track cars for a much
smoother gear setup.
Must be used with THP2404 axle. |
 |
$9.79
|
|
THPR47 |
Aluminum 64-P setscrew
spur gear / steel pinion gear ratio 12-47.
Will fit sidewinder Fly and GB-Track cars for a much
smoother gear setup.
Must be used with THP2404 axle |
 |
$9.79
|
|
THPR48 |
Aluminum 64-P setscrew
spur gear / steel pinion gear ratio 11-48.
Will fit sidewinder Fly and GB-Track cars for a much
smoother gear setup.
Must be used with THP2404 axle |
 |
$9.79
|
|
TSC01 |
Guide
flag, glass-reinforced Nylon. Fits TSR24 and TSR32 cars, perfect for Carrera
track, needs shortening on older tracks shallow slots.
Upgrade to
TSC25 for best results! |
 |
$0.99
|
|
TSC25 |
New stainless steel guide pin for all
TSRF chassis. Allows full rotation of chassis in the slot on narrow-slot
tracks. Suitable for all kinds of tracks. Direct bolt-on or custom
installation.
See assembly
instructions here |
 |
$2.99
|
|
TSC02 |
Spacer
washer, glass-reinforced Nylon. Used when chassis is set in longest
wheelbase. |
 |
$0.39
|
|
TSC03 |
Body-mounting
pin-tubing
stops (4 per car) glass-reinforced Nylon. Used when body is mounted with
straight pins. Set of 4: |
 |
$0.69
|
|
TSC04 |
Guide
spacer, glass-reinforced Nylon. Used when chassis is set in short or medium
wheelbase. |
 |
$0.79
|
|
TSC05 |
Guide
screw, 2-56, stainless steel |
 |
$0.19
|
|
TSC06 |
Nut,
2-56, (3 per car) stainless steel. Each: |
 |
$0.12
|
|
TSC07 |
Body
mount screw, (2 per car) 2-56, stainless steel. Each: |
 |
$0.19
|
|
TSC08 |
Front
axle E-clip (2 per car), cad-plated steel. Each: |
 |
$0.08
|
|
TSC09 |
Braided
contact, (2 per car) braided copper strands. Set: |
 |
$0.49
|
|
TSC10 |
Neodymium
traction magnet |
 |
$1.99
|
|
TSC11 |
Body
mounting pin, (4 per car) plated brass. Set: |
|
$0.19
|
|
TSC12 |
Guide
flag with longer blade for commercial tracks, glass-reinforced Nylon. Length
of blade is increased by 2mm. This guide is included in T24002, T24003,
T24004, T24001A, T24001B, T24001C, T24001D. Each:
Upgrade to
TSC25 for best results! |
 |
$0.99
|
|
TSC13 |
Double-sided
tape body mounting kit (use with T2406 and T3206) |
|
N/A |
|
TSC14 |
2-pack
body mounting epoxy (use with T2406 and T3206) |
|
N/A |
|
TSC15 |
Flat
sheet lead weight w/ two-sided adhesive tape |
 |
$2.49
|
|
TSC17 |
Motor
fastening screw, 2mm stainless steel (2 per car) Each: |
 |
$0.25
|
|
TSC18 |
Hardware
kit with braided contacts for T24004, and T32004 chassis kits |
 |
$2.25
|
|
TSC19 |
Hardware
kit for RTR chassis T24002 and T32002 |
 |
$1.25
|
|
TSC20 |
Hardware
kit with braided contacts for basic chassis kit T24003, T24003HPF, T32003
and T32003HPF |
 |
$0.99
|
|
TSC22 |
2-56
setscrew for TSRF32 spur gears and wheels set of 4: |
|
$1.00
|
|
TSC23 |
Hardware
kit with braided contacts for T24004HPF, and T32004HPF chassis kits |
 |
$1.99
|
|
TT06 |
.035" & .5mm hex wrench for TSR and most 1/32 scale alloy wheels & spur
gears
|
 |
$7.95
|
|
TSC30 |
1mm anodized aluminum
axle spacer for all TSR chassis kits. Each: |
|
$0.49
|
|
TSC31 |
3mm
anodized aluminum axle spacer for all TSR chassis kits. Each: |
|
$0.69
|